Michell TecnoDec Turntable
£795

Offered by: Fanthorpes HiFi, Hull - United Kingdom

Michell TecnoDec Turntable

This product is listed as Used

Price: £795 Buy It Now!

Advert reference: 13108

Listed in: Turntables

We have this preowned Michell TecnoDec Turntable (no cartridge) in Black.

It is in good condition which can be seen in the pictures attached. There are some hairline marks on the plinth but is in good general condition. It does not have its original box and due to the fragile nature of the turntable this listing is COLLECTION ONLY.

 

Michell Tecnodec Turntable

Details

Michell have been building quality audio turntables for over 35 years now, which makes them one of the oldest manufacturers still in business. The Michell GyroDec turntable has been around for over 25 years, and even its first incarnation can still be upgraded to the latest status. Michell turntables are precision instruments, built to last, and to reproduce sound as close as possible to the mastertape

The task of a turntable seems to be simple. At audio frequencies, the arm should be kept locked above the groove, without any extraneous motion relative to the cartridge. And the groove should be dragged at a constant angular speed underneath the stylus. This means that over the whole frequency band of 10Hz up to 20 kHz and beyond, the whole loop made by record, platter, bearing, (sub) chassis, arm board, tone arm, and cartridge body should behave in an utterly rigid and non-resonant fashion. Any flexure of the same dimensions as the microscopic undulations in the groove detracts from sonic fidelity.

Michell turntables clamp the record to a hard platter. This flattens out warps, and it also couples the LP tightly to the platter so that internal resonances can be drained away from the stylus, as if the LP effectively is of a much higher thickness and rigidity.

The Michell TecnoDec is the new entry-level turntable, taking the low-noise DC motor and the impedance-matched platter of the Michell GyroDec, along with an advanced bearing on an elegant solid-plinth design with damped feet. The Michell TecnoDec requires no user-setup or maintenance.

Due to the delicate nature of Michell Turntables when shipped they need to be partly assembled to some degree or other, dependant on the model. They do come with full instructions and any advice is available from our sales staff.

 

  • Solid-plinth turntable with standalone motor
  • Acrylic/vinyl platter
  • Oil-pumping inverted bearing
  • High-quality standalone DC motor
  • Finished in black acrylic with aluminium metal parts

 

Michell Tecno Arm 'A'

Details

The Michell Tecno Arm A is a fundamental mechanical rebuild of the well-known RB250 tonearm, to which is added monolithic wiring of the highest quality. The Michell Tecno Arm A arm tube is bead-blasted and perforated, which disperses structural resonances and yields a lower effective mass. The arm wand is internally damped to reduce resonance further, and the headshell is machined flat, to allow true azimuth relative to the bearing cradle. After modification the bearings are re-adjusted for highest possible performance, according to original Rega procedures.

 

  • One-piece perforated arm casting with internal foam damping
  • Proprietary silver litz cable in a continuous run from cartridge to amplifier
  • PTFE dielectric, metal braided shielding, separate ground wire
  • Silver-plated cartridge clips and phono plugs
  • Two counterweights, matching cartridges of 4-7g and 7-13g
  • Vertical tracking force adjuster in steps of 0.1g
  • Vertical tracking angle adjuster
  • Finger locknut for easy arm removal or VTA adjustment

 

TI-1-56425

Ask Fanthorpes HiFi to contact you about this item


Offered by:

Fanthorpes HiFi logo

Fanthorpes HiFi

6 Hepworth's Arcade
Silver Street
Hull
hu1 1ju - United Kingdom


Phone: 01482 223096

Quote iDreamAV ref: 13108


Fanthorpes HiFi is a member of...